Home > Gun Parts > 68 Automag / Minimag
Choose a sub category:
Air Source Adapter (ASA) Barrel Frame
Mainbody Rail & Sear Trigger
Valve Parts
Sort By:
Page of 3
13" Braided Stainless Steel Hoses 13" Braided Stainless Steel Hoses

13" Braided stainless steel hose.

Price: $15.00
AM/MM On/Off Assembly AM/MM On/Off Assembly

Direct Replacement that fits both Automag and Minimag Stainless Valve Bodies.

Price: $24.00
AM/MM Sear Assembly AM/MM Sear Assembly

Sear Assembly includes everything you see here. Fits Automag, Minimag and Classic rails. Does NOT fit the Tac rail, which needs the RT Pro Sear Assembly.

Price: $25.00
AM/MM Sear Pin AM/MM Sear Pin

The sear has this special hardened steel axle that it rotates on. For Automags, Minimags and Classics, unless using the Tac rail - then the Emag/RT/RT Pro Sear Axle Pin is required.

Price: $5.00
Back Bottle Bolt Back Bottle Bolt

Classic Back Bottle Bolt. Holds the original back bottle adaptor to the rail assembly.

Price: $1.00
Barrel / Regulator Velocity Nut O-Ring 2-Pack Barrel / Regulator Velocity Nut O-Ring 2-Pack

Classic Barrel Oring for twist lock, bayonet mount barrels.
Also used with part #000845 Regulator Nut Assembly as the tension o-ring.

Price: $3.00
Barrel Assembly Minimag Barrel Assembly Minimag

Minimag Barrel for both hopper left and hopper right powerfeeds. Clear anodized finish.

Price: $55.00
Barrel Twist Lock Assembly - No longer produced Barrel Twist Lock Assembly - No longer produced

Twist lock assembly that holds the barrel in place. Needs to be pressed in and out.

Price: $12.00
Available only in secondary market
Blade Trigger Blade Trigger

Compatible with X-Frame / Intelliframe style grip frames.

Available in black or silver.

Price: $30.00
Bolt - Foamie Bolt - Foamie

Bolts from AGD are made from hardened stainless for extra long life. This is the foamie style.

Price: $35.00
Discontinued
Bolt - Foamieless Bolt - Foamieless

Bolts from AGD are made from hardened stainless for extra long life. This one is the Foamieless Style.

Price: $35.00
Bolt Spring Bolt Spring

The Bolt Spring fits all AGD markers regardless of age or type. They are made from very special square wire so they don't fold inside themselves when collapsed. Replace your old springs when they sag below the front of the bolt.

Price: $6.00
Bottom Bottle Adapter Bottom Bottle Adapter

1/8 inch NPT output mounts to the bottom of AGD grip frames.
Black anodized finish.

Price: $25.00
Bumper - LVL 7/Classic Automag 2-Pack Bumper - LVL 7/Classic Automag 2-Pack

This is a urethane washer that sits at the base of the power tube.
When the bolt returns, it hits this to decelerate.
Now sold in packs of 2.

Price: $4.00
C-Clip Aluminum Body-AM/MM/Pro/Emag C-Clip Aluminum Body-AM/MM/Pro/Emag

Holds washer in place in all our Aluminum MainBodies

Price: $1.00
Field Strip Screw Assembly Field Strip Screw Assembly

The Field Strip Screw holds your valve in place. Also fastens the Emag battery to the frame.

Price: $12.00
Field Strip Screw Washer 2-Pack Field Strip Screw Washer 2-Pack

Prevents Field Strip Screws from loosening. Fits all guns except the Automag RT. Sold in packs of 2.

Price: $2.00
Foamie 4-Pack Foamie 4-Pack

Rubber foamies go easy on paint! These are replacements for the foamie bolt. Glue them in with superglue and let dry overnight.
Pack of 4.

Price: $4.00
Front Frame Screw AM/MM Front Frame Screw AM/MM

10-32 button-head cap screw that holds the front of the gripframe to an Automag or Minimag mainbody.
This is the shorter screw for AM/MM only.

Price: $1.00
Front Grip (Screw In) Gas Thru Front Grip (Screw In) Gas Thru

Gas thru vertical foregrip that screws into the RT Pro's vertical ASA adapter. Available only in flat black. Comes with Black foam grip.

Price: $25.00
Intelliframe/ X- Frame Safety Assembly Kit Intelliframe/ X- Frame Safety Assembly Kit

For the Intelliframe.
4 pieces as shown.

Price: $10.00
L10 Bolt Kit L10 Bolt Kit

The Level 10 Low Impact Superbolt Kit reduces paint chopping. This is not a "drop-in and shoot" part - you'll need to tune it according to the enclosed instructions.

Price: $100.00
Large Regulator Spring-Retro Large Regulator Spring-Retro

The Retro Valve uses two coil springs behind the Regulator Piston.  This is the larger of the two. Should never need replacing - just keep it greased.

Price: $6.00
Level 10 Power Tube O-Ring (RT Reg Seat O-Ring) 4-Pack Level 10 Power Tube O-Ring (RT Reg Seat O-Ring) 4-Pack

The Regulator Seat O-ring is the business end of the regulator.  Replace if you are having problems with velocity.
Sold in packs of 4.

Price: $4.00
Nummech ULE/X-Mag/Angel-Thread Detents - Replaceable ball Nummech ULE/X-Mag/Angel-Thread Detents - Replaceable ball

Nummech Detent for all AGD's ULE Bodies, X-Mags and Angel-threaded markers.

Price: $15.00
On/Off Bottom On/Off Bottom

Bottom part in your On/Off assembly. Made from high quality 303 stainless.

Price: $9.00
On/Off Bottom - Retro On/Off Bottom - Retro

On/Off Bottom is the lower half of the assembly. It screws into the On/Off  Top.

Price: $16.00
On/Off O-Ring RT or ULT small 4-Pack On/Off O-Ring RT or ULT small 4-Pack

This urethane o-ring goes inside the On/Off Top and On/Off Bottom assembly. Also used in the top of the ULT on/off assembly.
Now sold in packs of 4.

Price: $4.00
On/Off Pin - AM/MM On/Off Pin - AM/MM

The On/Off Pin controls air flow in your marker. It is a critical precision component and should not be modified. Hardened and chrome plated for extra long life.

Price: $6.50
On/Off Top On/Off Top

This part is one of several in the On/Off assembly. They all have names that start with On/Off to let you know where they go. This part can go in either way. Precision part, do not substitute with aftermarket items.

Price: $8.00