Home > Gun Parts > Classic RT
Choose a sub category:
Air Source Adapter (ASA) Barrel Frame
Rail & Sear Trigger Valve Parts
Sort By:
Page of 1
13" Braided Stainless Steel Hoses

13" Braided stainless steel hose.

Price: $15.00
Barrel / Regulator Velocity Nut O-Ring 4-Pack

Classic Barrel Oring for twist lock, bayonet mount barrels.
Also used with part #000845 Regulator Nut Assembly as the tension o-ring.

Price: $4.00
Barrel Assy-RT/RT Pro - Powerfeed Only

Original 11" RT Barrel with Ported Stainless Tip - fits any of our steel powerfeed mainbodies.

Price: $53.00
Blade Trigger

Compatible with X-Frame / Intelliframe style grip frames.

Available in black or silver.

Price: $30.00
Bottom Bottle Adapter

1/8 inch NPT output mounts to the bottom of AGD grip frames.
Black anodized finish.

Price: $15.00
Emag/RT Pro/RT Sear Axle Pin

Screws in the side of the marker into the sear bushing.

Price: $7.00
Field Strip Banjo Bolt Assy/RT

Completely assembled banjo bolt for your RT.

Price: $16.00
L10 Bolt Kit

The Level 10 Low Impact Superbolt Kit reduces paint chopping. This is not a "drop-in and shoot" part - you'll need to tune it according to the enclosed instructions.

Price: $100.00
L10 Power Tube O-Ring (RT Reg Seat O-Ring) 4-Pack

The Regulator Seat O-ring is the business end of the regulator.  Replace if you are having problems with velocity.
Sold in packs of 4.

Price: $4.00
Large Regulator Spring-Retro

The Retro Valve uses two coil springs behind the Regulator Piston.  This is the larger of the two. Should never need replacing - just keep it greased.

Price: $4.00
On/Off (small) O-Ring Retro 4-Pack

This urethane o-ring goes inside the On/Off Top and On/Off Bottom assembly. Also used in the top of the ULT on/off assembly.
Now sold in packs of 4.

Price: $4.00
On/Off Assembly .750 - RT ULE/RT Pro/Retro/RT/X-Valve

This is the stock On/Off Assembly for the RT ULE Custom, RT Pro Retro Valve, X-Valve and old Automag RT markers.

Price: $35.00
On/Off Bottom - Retro

On/Off Bottom is the lower half of the assembly. It screws into the On/Off  Top.

Price: $13.00
On/Off Top - Retro

On/Off Top is the upper half of the assembly. The On/Off Bottom screws into it.

Price: $10.00
Reg Valve Pin Assembly - Retro

The Regulator Pin comes as an assembly.  Just push it in place and it should be good to go.  If you have problems with this part call the factory.

Price: $27.00
Reg. Body O-Ring Retro 3-Pack

The Reg. Body O-Ring seals the two halves of the Valve Body together. Comes in the Parts Kit also.
Sold in packs of 3.

Price: $3.00
Reg. Valve Pin O-Ring - Retro/Reg Seat 3000 4-Pack

Marker: Four of these size O-rings are used in the Retro Valve pin assembly.
Flatline: Regulator seat for the Flatline 3000 only.
Sold here in a 4-pack.

Price: $4.00
Regulator Nut Assembly - Retro

The Regulator Nut screws into the back of the valve and adjust the velocity.  Keep the threads lubricated with a good grease.

Price: $15.00
Regulator Piston Assembly - Retro/RT

The Regulator Piston comes as an assembly that has a built in blow-off valve. Do not disassemble! Replace this part when air is venting out the back of the marker and you are shooting less than 300 FPS.

Price: $25.00
Regulator Seat Holder - Retro

The Regulator Seat Holder holds the O-ring that acts as the regulator seal.

Price: $8.00
RT Banjo Bolt O-Ring 4-Pack

For RT Banjo Bolts only.
Now sold in packs of 4.

Price: $4.00
Rt Classic Z-Lock Screw

Special Z-Lock Screw Pin created specifically for the Classic RT. Tiny z-lock screw that threads into the back regulator half of the classic RT valve to properly align the valve for the body and banjo bolt. Screws are loctited into place and removal of old screw can be difficult.

Price: $5.00
RT Rail Assembly

For use only with old Automag RT. Rail comes complete with a Twist Lock Assembly and Bushing installed. Available in black only.

Price: $90.00
Small Reg. Spring - Retro

This is the smaller of the two springs that go under the Reg Nut in the back of the valve.  The springs assemble one inside the other.

Price: $4.00
Yang Trigger

Compatible with X-Frame / Intelliframe style grip frames.

Available in black or silver.

Price: $30.00
Yin Trigger

Compatible with X-Frame / Intelliframe style grip frames.

Available in black or silver.

Price: $30.00