Home > Legacy Parts > Warp Feed
Sort By:
Page of 1
Axle Assembly Axle Assembly

Pulley assembly inside Warp snap fits in.

Price: $20.00
Board Mount Screw Board Mount Screw

Screws that mount the PC board. Do NOT over tighten.

Price: $0.50
Motor Mount Screw Motor Mount Screw

Motor Mount Screw

Price: $0.50
PF Plug 'P' Style Long PF Plug 'P' Style Long

Used when feeding the Warp hose into the bottom of the power feed tube. Allows switching back and forth between Warp and hopper.

Price: $9.00
Pulley Drive O-Ring 3-Pack Pulley Drive O-Ring 3-Pack

O-ring acts as a drive belt to turn Warp. Pack of 3.

Price: $3.00
Square Nut Square Nut

Standard 10-32 square nuts available at your local hardware store.

Price: $0.50
Super Hose Super Hose

Need hose longer than 11"? Try this super-hose! It contains metal wire coil and is very flexible, stretchy and strong. 14" super-hose stretches as far as two feet easily.

Price: $12.00
Warp Adapter 90 Degree Warp Adapter 90 Degree

90 Degree Feed Adaptor is used with vertical feed markers to keep the feed hose low on the marker. Includesone PF Plug "P" Style Short (Part #001387) at no extra charge.

Price: $14.00
Warp Adapter Lower Warp Adapter Lower

Fits into the output port of the Warp.

Price: $6.00
Warp Adapter Upper Warp Adapter Upper

Fits the marker's feed tube to the Warp feed hose.

Price: $6.00
Warp Center Hub Warp Center Hub

Center hub of feed wheel.

Price: $6.00
Warp Center Hub Screw Warp Center Hub Screw

Standard 10-32 socket head cap screws can be found at your local hardware store.

Price: $0.50
Warp Contact Spring Warp Contact Spring

Two of these small springs make contact with the sensor and the bottom of the PC board. About 1/8" long in real life, not shown actual size.

Price: $1.00
Warp Diverter Plate Warp Diverter Plate

Diverts the paintballs out the exit port.

Price: $5.00
Warp Dust Cover Warp Dust Cover

Dust cover goes on with the circuit board.

Price: $3.00
Warp Feed Gear 1 Warp Feed Gear 1

Make sure you tighten both mounting screws equally when assembling feed wheel.

Price: $10.00
Warp Feed Loader Motor Assembly Warp Feed Loader Motor Assembly

Motor comes with pulley assembled as a unit. Connections must be soldered.

Price: $15.00
Warp Hose O-Ring - 6-pack Warp Hose O-Ring - 6-pack

Hose O-Rings for the Warp. Use three on each end of the Warp Hose to insure a tight fit.
Sold in packages of 6.

Price: $1.20
Warp Housing Nut Warp Housing Nut

Standard 10-32 nuts. Get them at any hardware store.

Price: $0.50
Warp Housing Screw Warp Housing Screw

Warp Housing Screw

Price: $0.50
Warp Lid Black Warp Lid Black

Back cover plate for the PC board and motor.

Price: $5.00
Warp Mount - No Longer Produced Warp Mount - No Longer Produced

One piece aluminum mounting plate for Warp. Adjustment slots at each end.

Price: $25.00
Warp Mount Screw Warp Mount Screw

Standard 10-32 socket head cap screws 5/8ths of an inch long. Get them at your local hardware store.

Price: $0.50
Warp Plate Warp Plate

When assembling these parts make sure there is equal tension on both screws.

Price: $6.00
Warp Sensor & Rivet Warp Sensor & Rivet

Sensor must be pop riveted in place; Feel free to call Airgun Designs Tech Department for installation help. Sensor comes with the pop rivet.

Price: $6.00
Warp Shunt (Jumper) Warp Shunt (Jumper)

Used to program the Warp to set dwell time and input signal.

Price: $0.25
Warp Urethane Disc 2-Pack Warp Urethane Disc 2-Pack

If one disc in your warp has gone bad, you need to replace both, so we sell these by the pair.

Price: $12.00